Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Duct Repair & Sealing in Houston: What to Know First
We provide independent Abatement Technologies duct repair & sealing in Houston, with most residential jobs completed in a single scheduled visit and a written price delivered before any panel comes off. As an independent Abatement Technologies service provider, we service the equipment without manufacturer authorization, using OEM or quality aftermarket parts selected for each specific failure. Typical turnaround from call to completion is 3-5 business days for standard repairs, with documented photo records included on every visit. This page is for Houston homeowners who own Abatement Technologies air filtration, HEPA, or negative air systems connected to ductwork and need sealing, flex repair, or metal duct restoration. Call (346) 251-8919 for a free estimate with a written price.
How Abatement Technologies Products Fail - and How We Fix Them
- Abatement Technologies HEPA-AIRE PAS2400 and PAS1200 portable units: The flexible intake hose, which connects the HEPA unit to the duct system’s access port, fatigues at the collar clamp points after repeated pressurization cycles in Houston’s heat. The photo goes first. The pitch comes later, if it’s warranted. We replace with reinforced flex duct rated for negative-pressure extraction (suction-based debris removal) rather than patching, because a patched collar on a PAS series will leak and drop your capture efficiency below the 99.97% these units are specified for.
- Abatement Technologies Predator 1200 and Predator 600 air scrubbers: The 12-inch diameter flex duct runs that feed these units from ceiling plenums (the main distribution box above your HVAC) sag in Houston’s attic heat, creating low spots where condensation pools. We’ve found this in Energy Corridor homes where the attic hits 140°F in July. We re-support the duct run with metal strap, seal the sag point with mastic sealant (a thick, brush-applied paste that hardens to an airtight finish), and verify with a smoke pencil test.
- Abatement Technologies PREDATOR 1200 with built-in pre-filter housing: The gasket seal between the pre-filter door and the main housing compresses permanently after roughly 18 months of Houston’s ozone-heavy summer air. This bypasses unfiltered air directly into the HEPA stage, loading it prematurely. We replace the OEM gasket or machine a silicone replacement when OEM is back-ordered, then pressure-test the housing to confirm zero bypass.
- Abatement Technologies DUCTMASTERS and CAP600 central systems: The metal duct transitions at the unit connection point crack from thermal cycling, especially in Houston homes where the HVAC runs hard from March through November. We cut back to sound metal, fabricate a custom transition with Pittsburgh-lock seams (interlocking folds that don’t require screws), and seal with mastic rather than foil tape, which degrades in attic heat within two years.
- Abatement Technologies PREDATOR and HEPA-AIRE units on retrofit installs: The original contractor often uses standard flex duct rather than the antistatic, wire-reinforced flex specified for negative-pressure systems. In Houston’s high humidity, standard flex collapses under suction and traps moisture against the inner liner, breeding mold. We replace with Nikro or Abatement Technologies-specified flex duct and photograph the collapse damage for the customer record.
Our Abatement Technologies Duct Repair & Sealing Process
- 1
Inspection and photo documentation. We access every duct run with a borescope camera, photograph the failure, and show the customer before discussing scope. Haven Standard Clause 1: Written Price Before Work Starts.
- 2
Parts identification. We verify whether the failed component is available as Abatement Technologies OEM or if a quality aftermarket equivalent meets or exceeds the specification. We document this decision in writing.
- 3
Written price delivery. The customer receives one flat price per system, agreed in writing, before any repair begins. No per-foot or per-vent add-ons.
- 4
Repair execution. We cut, fabricate, seal, or replace using the selected parts, with all mastic cure times observed per manufacturer data, not rushed.
- 5
Pressure verification and photo closeout. We test sealed systems with a manometer (pressure gauge) or smoke pencil, then photograph the completed repair for the Documented Photo Record delivered to the customer.
- 6
Written guarantee. The 365-Day Done Right Promise is printed and signed, backed by Haven Standard Clause 5: Accountable Workmanship.
BeforeAfterWhat Abatement Technologies Duct Repair & Sealing Costs in Houston
These are the ranges we see on actual Abatement Technologies jobs in Houston, based on 52,000+ homes served since 2013:
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Flex duct section replacement (single run) | $280-$450 | Length, attic accessibility, whether the plenum connection is also compromised |
| Metal duct transition repair or fabrication | $340-$620 | Custom fabrication needed, gauge of original metal, number of seams |
| Mastic sealant application (whole system) | $480-$780 | System size, number of registers (the visible vents in each room), existing tape removal |
| HEPA-AIRE or Predator hose/collar replacement | $180-$320 | OEM vs. quality aftermarket, whether the clamp point damage extends into the main housing |
| Pre-filter housing gasket replacement | $140-$240 | Gasket availability, housing surface condition requiring resurfacing |
Every price is flat per system, agreed in writing before work starts. No per-vent pricing. No add-ons after the truck arrives. Call (346) 251-8919 for an exact quote - estimates are free.
Why Houston Homeowners Call CleanRun Air Duct Cleaning Houston for Abatement Technologies Work
Tomas Reyes, who leads our operation, put in years on Abatement Technologies equipment across the northeast before relocating to Houston, where Gulf Coast humidity turned out to be a different kind of stress on duct systems than freeze-thaw cycling. We’ve documented PAS series collar failures, Predator flex sags, and DUCTMASTERS transition cracks with before-and-after photos on every job since 2013. Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews, and we also service Lennox, Trane, and Carrier systems when a Houston home has mixed-brand HVAC. The 365-Day Done Right Promise is in writing, not a policy subject to manager approval. If the work is not right, we make it right.
FAQs
Repair work on the duct connections and flex runs does not void the Abatement Technologies equipment warranty, provided the repair does not alter the unit’s electrical or filtration specifications. We use OEM or equivalent parts and document everything, so the warranty record stays clean. If your unit is still under manufacturer warranty, we note the serial number and service date in our job record for your files. Call (346) 251-8919 if you need help verifying your warranty status.
Most Abatement Technologies gaskets, collars, and standard flex sections arrive within 3-5 business days to our Houston warehouse. For older Predator 600 units or discontinued lines, we machine quality aftermarket equivalents in-house rather than leaving a system down indefinitely. We tell you the lead time in writing before you agree to the job. Call (346) 251-8919 for current availability on your specific model.
Repair is the right call when the failure is isolated to flex sections, gaskets, or transition points and the HEPA or negative-air unit itself tests to specification. We recommend replacement when the unit has multiple compressor cycles, housing cracks, or parts obsolescence that makes future repair uneconomical. Our inspection includes a written recommendation with the photo evidence behind it. Call (346) 251-8919 for an honest assessment.
You receive a Documented Photo Record of every duct run, before and after, as a standard deliverable on every CleanRun job. We also pressure-test sealed systems and record the manometer reading. This is not a policy; it is Haven Standard Clause 2: Verifiable Results, practiced on every visit since 2013. If a company cannot show you the inside of your ducts, they did not document their work. Call (346) 251-8919 and we will explain what to ask any contractor before you hire them.
We provide a Free Second Opinion on any written estimate. Bring a competitor’s quote; we put our own number next to it in writing, with a line-item breakdown of parts, labor, and guarantee terms. We do not match bait-and-switch pricing - a $79 teaser that becomes $800 on arrival is not a quote we will emulate. Call (346) 251-8919 to schedule your second opinion.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Houston at CleanRun Air Duct Cleaning Houston, serving Houston and nearby areas.